杭州雄盛机械有限公司

  • 点焊机维护注意事项
  • 本站编辑:杭州雄盛机械有限公司发布日期:2019-10-18 19:11 浏览次数:
  1、点焊机操作人员不得以身体任何部位或任何物件靠近触摸传动的齿轮、传动槽轮、链轮、皮带、链条、调直机、感应体、接近开关以及电柜内、变压器等带有危险电压的导体部分。                                                       
 
2、点焊机操作人员不得把手或物体靠近正在加压运动的上电极或放入上、下电极之间。
 
3、点焊机操作人员不得带电插或碰掉焊网电源变压器上的功率调节插把,不得掀起防护板。4、点焊机操作人员不得拆掉、碰断主机和电控柜上的接零(接地)安全保护线,定期检查接零(接地)安全保护线是否良好。
 
5、当点焊机电控柜内有熔断时,应先停机停电,由电工查出熔断原因之后,再以相同型号规格的熔芯更换,否则将引起火灾和烧毁器件。
 
6、点焊机操作人员不得随意调整电控柜内的器件,不得随意把工具、铁丝等杂物放入电控柜或放在机箱顶部以及齿条上。
 
7、点焊机操作人员必须及时对轴承、滑块、滑道、滑套、链轮、链条、齿轮、齿条等滚动摩擦的零部件加注润滑油,不得缺油运转。加注润滑油应在停机后进行。必须在运行中加
 
 
注润滑油的部位,不得以加油器具碰触运行中的机构,可采用滴注方式。
1. The operator of spot welder shall not touch any part of the body or any object near the transmission gear, transmission groove wheel, sprocket wheel, belt, chain, straightening machine, induction body, proximity switch, electric cabinet, transformer and other conductor parts with dangerous voltage.
 
 
 
2. The operator of spot welder shall not put his hand or object near the upper electrode which is moving under pressure or put it between the upper and lower electrodes.
 
 
 
3. The operator of the spot welder shall not plug or touch the power adjustment plug on the power transformer of the welding mesh, and shall not lift the protection plate. 4. The operator of spot welder shall not remove or break the safety wire connecting zero (ground) on the main machine and electric control cabinet, and regularly check whether the safety wire connecting zero (ground) is in good condition.
 
 
 
5. When there is a fuse break in the mechanical and electrical control cabinet of spot welding, the machine should be shut down and power cut first. After the electrician finds out the cause of the fuse break, the core of the same model and specification should be replaced.
 
 
 
6. The operator of spot welder shall not randomly adjust the components in the electric control cabinet, and shall not randomly put the tools, wire and other sundry objects into the electric control cabinet or on the top of the machine case and rack.
 
 
 
7. The operator of spot welding machine must fill lubricating oil for the rolling friction parts such as bearings, sliders, slideways, sliding sleeves, sprockets, chains, gears and rack in time, and must not run short of oil. Lubricating oil filling shall be carried out after shutdown. Must be added in operation
 
 
 
 
 
The place where lubricating oil is poured shall not be touched by the oiler with the running mechanism, but by drip.
南通启重润滑设备有限公司 幸运彩票app 专业玩彩 猪猪棋牌 江西11选5 幸运彩票app 欧洗干洗店加盟 金利集成灶官网 广州鑫伟展览工程有限公司 依米康